Pictured in specialty Cerakote finish by Koted Arms.
Independent, elusive and if cornered will fight hard for it’s freedom all while being a dazzling beauty.. Unicorns sound a lot like you, and the rest of our AR15 loving, badass friends .. so, it seamed kinda perfect to have a Unicorn design be the next rail in our line up.
Now, we couldn’t just come out with any unicorn design, no typical cartoon, my little pony, kinda Unicorn was going to cut it, this is the OffHand Gear squad we were designing this magical creature for ..it had to have a flair of badassery with a bit of Charlies Angels thrown in there too. Of course, like our other hand guards, this one is a smaller diameter making it easier to hold onto there are pre-drilled holes on the top and bottom to attach our pictainny rail (sold separately) to, adding any accessories ( you know how we love our accessories) like your favorite scope, laser sight or bi-pod won't be an issue.
So get your Unicorn on, hit the range and show everyone you and your rifle are not some docile little powder puff, but instead the magical badass creature you really are!
- Available in 3 sizes, 9", 12" and 15"
- Weight in raw - 6.2oz, 8.2oz and 10.0oz
- Free float design
- Smaller diameter fits smaller hands better (2" exterior / 1.75" interior)
- Beveled edges makes for a smooth finish, rings and gloves don't hang up on.
- Made from 6061 t6 aluminum
- Includes AR15 barrel nut and mounting screws
- Pre-drilled and tapped on both top and bottom. Picatinny / tac rail available (sold separately)
- CeraKote brand color coating. Comes in Raw as a stocked option. For other CeraKote color please see color chart and include color name and number in your order notes. (Please allow additional time for this option).
- Please note that a low profile gas tube will be necessary for installation.
- AR10 barrel nut and mounting screws available as an upgrade
Yes - Lifetime Warranty
Yes, any low profile gas block will work though.
No, you can use any standard armorer's wrench to install the hand guard.
No, unfortunately it wont :( Not to say we might have that available one day, but right now sorry to say it is not.
Yes, you can with the use of our tactical rail pieces. These are designed specifically to work with smaller radius of our hand guards. You can shop the tac rail options here.
Yes, if your Airsoft rifle has a standard mil spec threaded upper - Mil spec standard is 1.250" x 18 tpi.
Handguard Mounting Instructions and Tips:
Before mounting handguard insure your receiver is mil-spec. If not, confirm fit of parts before beginning mounting instructions. Some non mil-spec receivers require barrel nut to be backed away from the upper receiver to allow clearance of over sized front lugs.
Step: 1) Once you have the old free float-tube and/or barrel nut removed, clean any grease or oil from the threads of the upper receiver extension.
Step: 2) This step is optional to allow easier installment of handguard. LocTite® is not required for installation of handguard. Apply a drop or two of blue LocTite® to the receiver threads and screw the large aluminum barrel-nut on until it stops, then back it off until the gas tube holes line up.
Step: 3) Insert the barrel and slide the steel castle bolt over the barrel and thread it into the aluminum barrel-nut; now, use a .184″ or 3/16″ bit or punch to to keep the gas tube holes aligned .
Step 4) With the punch inserted in the gas tube holes turn the steel castle bolt by hand until you get a good, solid hand-tight alignment with the barrel-nut and receiver. Once you have the two aligned, let it set for a 2-24 hours. After the blue LocTite® has cured between the barrel-nut and receiver, the steel insert and barrel can be removed.
Step 5) For final assembly insert the barrel, thread the steel castle bolt into the barrel-nut and once it is finger tight. Optional: Then back it off three or four turns and place a drop of blue LocTite® on the threads of the steel insert, right where it becomes visible out of the barrel-nut.
Step 6) Now torque the steel insert down to desired torque (according to your rifle manufacturer’s specifications). This can all be accomplished with or without the use of punch in the gas tube but the barrel-nut can move while you are torquing the steel castle nut, and then you will have to loosen it up and re-time it. We recommend using the punch to insure proper timing.
Step 7) Once you have installed the gas tube, slide the handguard onto the barrel nut and aligned the 6 radial holes with the corresponding holes in the barrel-nut. Now the 6 countersunk screws can be installed. Tighten until snug. DO NOT over tighten. Stripped screws are not covered by the warranty.